Smith & Wesson M&P Shield Safety Alert
S&W M&P Shield Safety Alert
PRODUCT: ALL M&P Shield™ firearms manufactured before August 19, 2013.
DESCRIPTION OF THE HAZARD: Smith & Wesson has identified a condition where the trigger bar pin could damage the lower trigger in certain M&P Shields in a way that may affect the functionality of the drop safety feature of the firearm, potentially allowing the pistol to discharge if it is dropped.
Any unintended discharge of a firearm has the potential to cause injury, and we ask that you STOP USING YOUR PISTOL IMMEDIATELY UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED.
DESCRIPTION OF THE PRODUCT INVOLVED: This Safety Alert applies to all M&P Shield pistols manufactured before August 19, 2013. We believe this condition is largely limited to recently manufactured M&P Shield pistols. However, out of an abundance of caution, we are asking all consumers of all M&P Shields manufactured before August 19, 2013 to immediately inspect their pistols for this condition.
INSPECTING YOUR PISTOL: Your firearm must be inspected to determine whether it exhibits the condition identified in this notice. To determine whether your firearm is affected by this condition, please inspect your firearm as follows (click here for video instructions):
1. Follow the procedures in your Safety & Instruction Manual to ENSURE THE FIREARM IS UNLOADED; ENSURE THAT THE MUZZLE IS POINTED IN A SAFE DIRECTION; THE SLIDE IS LOCKED BACK; AND THE MANUAL SAFETY IS ENGAGED.
2. Hold your pistol sideways with the muzzle pointed to the left. Look at the trigger. Note that the trigger is actually two pieces, with a pin in the middle that connects the two halves (Figure 1).
3. Look at Figure 2. Without touching the trigger, identify the plastic tab circled in red in Figure 2.
4. Slowly pull the trigger. The plastic tab encircled in Figure 2 should disappear into the upper trigger section (Figure 3).
5. Slowly release the trigger. The tab should reappear as shown in Figure 2 completely on its own.
6. Repeat steps 4 and 5 several times. If the small tab as shown in Figure 2 reappears each time, your pistol does not require repair.
7. If the small tab does not consistently reappear as shown in Figure 2, YOUR PISTOL MUST BE RETURNED FOR SERVICE.
If you are uncomfortable conducting the inspection outlined above, or are unsure whether the condition described in this notice applies to your firearm, please take your firearm to your local M&P Certified Armorer or send your firearm to Smith & Wesson for inspection. M&P Armorers can be found on the Smith & Wesson website under Find a Dealer.
If after inspection it is determined that the condition outlined in this safety alert exists, the firearm must be sent to Smith & Wesson for repair.
REMEDY/ACTION TO BE TAKEN: STOP USING YOUR FIREARM UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED.
Your firearm must be inspected to determine whether it exhibits the condition identified in this notice. To determine whether your firearm is affected by this condition, please inspect your firearm by following the inspection instructions above.
If your firearm is affected by the condition outlined in this notice, please send your pistol to Smith & Wesson. Your firearm will be inspected, and if necessary, repaired at no cost to you. Your firearm will be returned within 5 to 7 business days. All shipping and repair costs will be covered by Smith & Wesson.
Outside the United States, click here for a list of Authorized Warranty Centers that will repair your pistol.
CONSUMER CONTACT: Please contact Smith & Wesson directly at 877-899-6259 to arrange for the repair, if necessary, of your pistol.
Yes i have a S&W 9mm model SW9VE and have lost the spring for the gas chamber and won’t fire semi just one round at a time.Thank you for your time and hope you can help me out… Jeff Sargent (xxx)xxx-xxxx (number removed — GL)
Numrich has most gun parts. If you need help, start a thread on the GunLink Forums and I’m sure you’ll get the answers you’re looking for.